DIY DTG - Build your own Digital T-Shirt Printer

Search found 144 matches

  • 1
  • 2
  • 3
  • 4
  • 5
  • 15
by ddelgrande
Fri Mar 17, 2017 10:06 am
Forum: DIY Pretreat Machine
Topic: OpenDTG Pre-Treater Build
Replies: 10
Views: 262

Re: OpenDTG Pre-Treater Build

So I have everything I need to build the pre-treater, so a few more questions:  1.  I'm building the base out of OpenBuilds V-Slot Gantry Set and V-Slot Linear Rail coupled to 1 1/2" PVC Schedule 40 pipe.  I will T the pipe to build the riser extensions but wonder where I should place those ext...
by ddelgrande
Mon Mar 13, 2017 4:58 pm
Forum: Arduino Open Source DIY DTG
Topic: Chip Resetter Install (soldering advice / pics!)... kinda/sorta URGENT!
Replies: 17
Views: 658

Re: Chip Resetter Install (soldering advice / pics!)... kinda/sorta URGENT!

I blew up two mainboards because I was trying to make things look pretty.  In both cases, it was a fuse Andy pointed and I just did a bridge solder.  Andy is correct, Epson service centers won't fix a mainboard, you have to buy a new or used printer. 
by ddelgrande
Mon Mar 13, 2017 4:53 pm
Forum: General - Start Here
Topic: Trying to print with ekrip
Replies: 22
Views: 258

Re: Trying to print with ekrip

Having bought the T-Dozer kit and then going with the OpenDTG AIO board I know the T-Dozer uses and inferior Nema 17 step motor.  I found it on ebay for $8 to $9 dollars.  The other thing is the T-Dozer uses a 14 tooth pulley.  In going with the AIO board I upgraded to a Nema 23 step motor and a 30 ...
by ddelgrande
Thu Mar 09, 2017 1:23 pm
Forum: DIY Pretreat Machine
Topic: OpenDTG Pre-Treater Build
Replies: 10
Views: 262

Re: OpenDTG Pre-Treater Build

Andy wrote:
ddelgrande wrote:
I believe the Bounce2.h library needs to be included in the Pre-Treater Build 00003.  Just need verification if this is correct. 

Thanks

Yes you need the Bounce2.h library

-------------
Might be a good idea to add that requirement to the Download section under OpenDTG Pre-Treater Board.
by ddelgrande
Wed Mar 08, 2017 8:19 pm
Forum: DIY Pretreat Machine
Topic: OpenDTG Pre-Treater Build
Replies: 10
Views: 262

Re: OpenDTG Pre-Treater Build

I believe the Bounce2.h library needs to be included in the Pre-Treater Build 00003.  Just need verification if this is correct. 

Thanks
by ddelgrande
Wed Mar 08, 2017 3:40 pm
Forum: DIY Pretreat Machine
Topic: OpenDTG Pre-Treater Build
Replies: 10
Views: 262

Re: OpenDTG Pre-Treater Build

alex24bog wrote:
hello in amazon usa what reference ..thanks

ebay
http://www.ebay.com/itm/24V-Seaflo-100- ... 1594991665
by ddelgrande
Wed Mar 08, 2017 10:09 am
Forum: General - Start Here
Topic: Why I can't see pictures of others users?
Replies: 11
Views: 395

Re: Why I can't see pictures of others users?

dme, to put into to perspective, $20 represents less than 1% of the total cost to convert a printer to DTG and print a shirt.  As a novice, without this forum, there's no way I would have been able to convert my P600 to a dtg printer and that's after buying a kit from another source that provided ze...
by ddelgrande
Tue Mar 07, 2017 11:35 am
Forum: DIY Pretreat Machine
Topic: OpenDTG Pre-Treater Build
Replies: 10
Views: 262

Re: OpenDTG Pre-Treater Build

Regarding the inlet arrow on the pump, it's on the bottom—a little black arrow.  So when looking at the pump from the top the flow should be as shown in the following pic: 

[attachment=0]pump.JPG[/attac
by ddelgrande
Mon Mar 06, 2017 10:28 am
Forum: General - Start Here
Topic: Stepper motor
Replies: 22
Views: 279

Re: Stepper motor

Here's what I ran into using the AIO board:  It seems the typical stepper wire schematics show the connections as 1A, 1B, and 2A, 2B meaning there's continuity between 1A-1B and 2A-2B.  Those standard connections don't match the AIO board, so the user has to make the correlation.   The ...
by ddelgrande
Mon Mar 06, 2017 7:00 am
Forum: DIY Pretreat Machine
Topic: OpenDTG Pre-Treater Build
Replies: 10
Views: 262

OpenDTG Pre-Treater Build

I starting to come up with my design for the OpenDTG Pre-Treater build using the OpenDTG Pre-Treater kit and have a few questions:  1.  The kit came with two vinyl tubes/tubing.  I can see how the smaller diameter of the two connects the pre-treater solution to the pump and the pump to the nozzle bu...
  • 1
  • 2
  • 3
  • 4
  • 5
  • 15